The Meross Smart Wi-Fi Thermostat is a Matter device (Vendor 0x1345, Product 0xE001) with 3 endpoints.

Last updated 4 Oct 2026

Smart Wi-Fi Thermostat (PID 0xE001)

★ ★ ★ ☆ ☆ (60%)

Meross

Vendor ID: 4933

Product ID: 57345

Seen: 229 times

No Binding Group control Scene control Wifi

CSA Certification:

Certified Sep 12, 2024 CSA24507MAT43962-24 v9.3.2

Links: 📖 Manual

What This Device Can Do

Climate

★ ★ ★ ☆ ☆ 55% of features

Controls
▶ 🌀 Fan speed control	v1.1	✓
Fan Control What you can do: • Adjust fan speed by one step Information available: ✓ Current fan mode (off/low/medium/high/auto) ✓ Fan mode sequence ✓ Target speed percentage ✓ Current speed percentage ✕ Speed max optional ✕ Speed setting optional ✕ Speed current optional ✕ Rock support optional ✕ Rock setting optional ✕ Wind support optional ✕ Wind setting optional ✕ Airflow direction optional
▶ 🌡️ Temperature setpoint	v1.0	✓
Thermostat What you can do: ✓ Raise or lower the target temperature ✓ Raise or lower the target temperature ✕ Set weekly schedule optional ✕ Get weekly schedule optional ✕ Add thermostat suggestion response optional ✕ Clear weekly schedule optional ✕ Set active schedule request optional ✕ Set active preset request optional ✕ Add thermostat suggestion optional ✕ Remove thermostat suggestion optional ✕ Atomic response optional ✕ Atomic request optional Information available: ✓ Current room temperature ✕ Outdoor temperature optional ✕ Occupancy optional ✓ Abs min heat setpoint limit ✓ Abs max heat setpoint limit ✓ Abs min cool setpoint limit ✓ Abs max cool setpoint limit ✕ Pi cooling demand optional ✕ Pi heating demand optional ✕ Hvac system type configuration optional ✕ Local temperature calibration optional ✓ Target cooling temperature ✓ Target heating temperature ✕ Unoccupied cooling setpoint optional ✕ Unoccupied heating setpoint optional ✓ Min heat setpoint limit ✓ Max heat setpoint limit ✓ Min cool setpoint limit ✓ Max cool setpoint limit ✓ Min setpoint dead band ✕ Remote sensing optional ✓ Control sequence of operation ✓ Current mode (heat/cool/auto/off) ✕ Thermostat running mode optional ✕ Start of week optional ✕ Number of weekly transitions optional ✕ Number of daily transitions optional ✕ Temperature setpoint hold optional ✕ Temperature setpoint hold duration optional ✕ Thermostat programming operation mode optional ✓ Thermostat running state ✕ Setpoint change source optional ✕ Setpoint change amount optional ✕ Setpoint change source timestamp optional ✕ Occupied setback optional ✕ Occupied setback min optional ✕ Occupied setback max optional ✕ Unoccupied setback optional ✕ Unoccupied setback min optional ✕ Unoccupied setback max optional ✕ Emergency heat delta optional ✕ Ac type optional ✕ Ac capacity optional ✕ Ac refrigerant type optional ✕ Ac compressor type optional ✕ Ac error code optional ✕ Ac louver position optional ✕ Ac coil temperature optional ✕ Ac capacityformat optional ✕ Preset types optional ✕ Schedule types optional ✕ Number of presets optional ✕ Number of schedules optional ✕ Number of schedule transitions optional ✕ Number of schedule transition per day optional ✕ Active preset handle optional ✕ Active schedule handle optional ✕ Presets optional ✕ Schedules optional ✕ Setpoint hold expiry timestamp optional ✕ Max thermostat suggestions optional ✕ Thermostat suggestions optional ✕ Current thermostat suggestion optional ✕ Thermostat suggestion not following reason optional ✕ Critical freeze protection optional ✕ Critical overheat protection optional ✕ Sensors optional ✕ Available sensor handles optional ✕ Enabled sensor handles optional ✕ Number of sensor schedule transitions optional ✕ Sensor schedule optional Enabled features: Heating

Sensors
▶ 💧 Humidity sensor	v1.0	✓
Relative Humidity Measurement Information available: ✓ Current humidity reading ✓ Minimum measurable humidity ✓ Maximum measurable humidity ✕ Tolerance
🌡️ Temperature sensor	v1.0	✕

Automation & Scenes
▶ 🎬 Scenes & presets	v1.3	✓
Scenes Management What you can do: ✓ Save current state as a scene ✓ Save current state as a scene ✓ View scene settings ✓ View scene settings ✓ Delete a saved scene ✓ Delete a saved scene ✓ Remove all scenes ✓ Remove all scenes response ✓ Activate a saved scene ✓ Activate a saved scene ✓ Recall scene ✓ List available scenes ✓ List available scenes ✕ Copy scene optional ✕ Copy scene response optional Information available: ✓ Currently active scene ✓ Fabric scene info
⏰ Scheduling	v1.0	✕

Comfort & Climate
▶ 🔥 Heating	v1.0	✓
Thermostat What you can do: ✓ Setpoint raise lower ✓ Get weekly schedule response ✕ Set weekly schedule optional ✕ Get weekly schedule optional ✕ Add thermostat suggestion response optional ✕ Clear weekly schedule optional ✕ Set active schedule request optional ✕ Set active preset request optional ✕ Add thermostat suggestion optional ✕ Remove thermostat suggestion optional ✕ Atomic response optional ✕ Atomic request optional Information available: ✓ Current room temperature ✕ Outdoor temperature optional ✕ Occupancy optional ✓ Abs min heat setpoint limit ✓ Abs max heat setpoint limit ✓ Abs min cool setpoint limit ✓ Abs max cool setpoint limit ✕ Pi cooling demand optional ✕ Pi heating demand optional ✕ Hvac system type configuration optional ✕ Local temperature calibration optional ✓ Occupied cooling setpoint ✓ Target heating temperature ✕ Unoccupied cooling setpoint optional ✕ Unoccupied heating setpoint optional ✓ Min heat setpoint limit ✓ Max heat setpoint limit ✓ Min cool setpoint limit ✓ Max cool setpoint limit ✓ Min setpoint dead band ✕ Remote sensing optional ✓ Control sequence of operation ✓ System mode ✕ Thermostat running mode optional ✕ Start of week optional ✕ Number of weekly transitions optional ✕ Number of daily transitions optional ✕ Temperature setpoint hold optional ✕ Temperature setpoint hold duration optional ✕ Thermostat programming operation mode optional ✓ Thermostat running state ✕ Setpoint change source optional ✕ Setpoint change amount optional ✕ Setpoint change source timestamp optional ✕ Occupied setback optional ✕ Occupied setback min optional ✕ Occupied setback max optional ✕ Unoccupied setback optional ✕ Unoccupied setback min optional ✕ Unoccupied setback max optional ✕ Emergency heat delta optional ✕ Ac type optional ✕ Ac capacity optional ✕ Ac refrigerant type optional ✕ Ac compressor type optional ✕ Ac error code optional ✕ Ac louver position optional ✕ Ac coil temperature optional ✕ Ac capacityformat optional ✕ Preset types optional ✕ Schedule types optional ✕ Number of presets optional ✕ Number of schedules optional ✕ Number of schedule transitions optional ✕ Number of schedule transition per day optional ✕ Active preset handle optional ✕ Active schedule handle optional ✕ Presets optional ✕ Schedules optional ✕ Setpoint hold expiry timestamp optional ✕ Max thermostat suggestions optional ✕ Thermostat suggestions optional ✕ Current thermostat suggestion optional ✕ Thermostat suggestion not following reason optional ✕ Critical freeze protection optional ✕ Critical overheat protection optional ✕ Sensors optional ✕ Available sensor handles optional ✕ Enabled sensor handles optional ✕ Number of sensor schedule transitions optional ✕ Sensor schedule optional Enabled features: Heating
▶ 💧 Humidity control	v1.1	✓
Fan Control What you can do: • Step Information available: ✓ Current fan mode ✓ Fan mode sequence ✓ Percent setting ✓ Percent current ✕ Speed max optional ✕ Speed setting optional ✕ Speed current optional ✕ Rock support optional ✕ Rock setting optional ✕ Wind support optional ✕ Wind setting optional ✕ Airflow direction optional
❄️ Cooling	v1.0	✕
🔄 Auto heat/cool	v1.0	✕
📌 Temperature presets	v1.0	✕

⚠ Not available: Scheduling

Setup & Reset Info

▼

Setup: Manual Control Reset: Standard

Additional Steps:

5,,0x01&0x02

Setup Guide

Technical Details For developers

▼

Device Compatibility

Can provide data to: These devices have client clusters that can read from or control this device's server clusters

Thermostat (3 devices)

Aqara Climate Sensor W100 (Aqara) Eve Thermo Control (Eve Systems) Touchscreen Switch S100 (Aqara)

Relative Humidity Measurement (1 device)

Touchscreen Switch S100 (Aqara)

Fan Control (2 devices)

Matter Thread Fan Switch VTM35-SN (Inovelli) Touchscreen Switch S100 (Aqara)

Spec Compliance & Feature Analysis

Comparing this device's clusters against Matter specification requirements. Shows what's implemented, what's missing, and bonus features. Note: Legacy clusters (e.g., Scenes) count as compliant when replaced by newer equivalents (Scenes Management).

Thermostat Matter 1.0 Compliant

★ ★ ★ ☆ ☆ Feature Score:

60%

Optional Not Implemented 5

Per the Matter spec, these clusters are optional. The device is compliant without them.

Energy Preference Fan Control (client) Temperature Measurement (client) Relative Humidity Measurement (client) Occupancy Sensing (client)

Bonus Features Implemented 2

Groups Thermostat User Interface Configuration

Extra (Beyond Spec) 5

Descriptor Fixed Label User Label Scenes Management Relative Humidity Measurement

2/2 required | 2/7 optional

Frequently Paired With Found in 10 installations

These devices are commonly found together in the same smart home setup based on anonymous telemetry data.

Matter Thread Dimmer Switch VTM31-SN Inovelli

8 shared 80% of installs

Matter Thread On/Off Switch VTM30-SN Inovelli

6 shared 60% of installs

MYGGBETT door/window sensor IKEA of Sweden

4 shared 40% of installs

ALPSTUGA air quality monitor IKEA of Sweden

4 shared 40% of installs

Essentials A19-A60 Nanoleaf

4 shared 40% of installs

Eve Energy Outlet Eve Systems

3 shared 30% of installs

Eve Energy Eve Systems

3 shared 30% of installs

KLIPPBOK water leak sensor IKEA of Sweden

3 shared 30% of installs

Endpoints by Version

Hardware: 9.0

SW: 9.3.2 Latest Seen 3 endpoints

Endpoint 0

Device Types

Server Clusters (hover for details)✓ Rich data

Endpoint 1

Device Types

Server Clusters (hover for details)✓ Rich data

Endpoint 2

Device Types

Server Clusters (hover for details)✓ Rich data

Known Versions

Hardware Version	Software Version	Count	First Seen	Last Seen
9.0	9.3.2	229	2026-01-04 04:48:21	2026-10-04 20:52:41

« Back to device index

Smart Wi-Fi Thermostat (PID 0xE001)

What This Device Can Do

What you can do:

Information available:

What you can do:

Information available:

Enabled features:

Information available:

What you can do:

Information available:

What you can do:

Information available:

Enabled features:

What you can do:

Information available:

Setup & Reset Info

Technical Details For developers

Device Compatibility

Thermostat (3 devices)

Relative Humidity Measurement (1 device)

Fan Control (2 devices)

Spec Compliance & Feature Analysis

Frequently Paired With Found in 10 installations

Endpoints by Version

Hardware: 9.0

Endpoint 0

Groups

Descriptor

Access Control

Basic Information

Localization Configuration

General Commissioning

Network Commissioning

Diagnostic Logs

General Diagnostics

Wi-Fi Network Diagnostics

Administrator Commissioning

Operational Credentials

Group Key Management

Fixed Label

User Label

Endpoint 1

Identify

Groups

Descriptor

Fixed Label

User Label

Scenes Management

Thermostat

Thermostat User Interface Configuration

Relative Humidity Measurement

Endpoint 2

Identify

Groups

Descriptor

Fan Control

Known Versions