The tado° GmbH tado Smart Radiator Thermostat X is a Matter device (Vendor 0x134E, Product 0x0001) with 5 endpoints.

Last updated 19 Jun 2026

tado Smart Radiator Thermostat X

★ ★ ★ ☆ ☆ (60%)

tado° GmbH

Vendor ID: 4942

Product ID: 1

Seen: 3,012 times

No Binding

CSA Certification:

Certified Nov 8, 2023 CSA23D71MAT41880-24 v1.0

What This Device Can Do

Climate

★ ★ ★ ☆ ☆ 27% of features

Controls
▶ 🌡️ Temperature setpoint	v1.0	✓
Thermostat What you can do: ✓ Raise or lower the target temperature ✓ Raise or lower the target temperature ✕ Set weekly schedule optional ✕ Get weekly schedule optional ✕ Add thermostat suggestion response optional ✕ Clear weekly schedule optional ✕ Set active schedule request optional ✕ Set active preset request optional ✕ Add thermostat suggestion optional ✕ Remove thermostat suggestion optional ✕ Atomic response optional ✕ Atomic request optional Information available: ✓ Current room temperature ✕ Outdoor temperature optional ✕ Occupancy optional ✓ Abs min heat setpoint limit ✓ Abs max heat setpoint limit ✕ Abs min cool setpoint limit optional ✕ Abs max cool setpoint limit optional ✕ Pi cooling demand optional ✕ Pi heating demand optional ✕ Hvac system type configuration optional ✕ Local temperature calibration optional ✕ Target cooling temperature optional ✓ Target heating temperature ✕ Unoccupied cooling setpoint optional ✕ Unoccupied heating setpoint optional ✕ Min heat setpoint limit optional ✕ Max heat setpoint limit optional ✕ Min cool setpoint limit optional ✕ Max cool setpoint limit optional ✕ Min setpoint dead band optional ✕ Remote sensing optional ✓ Control sequence of operation ✓ Current mode (heat/cool/auto/off) ✕ Thermostat running mode optional ✕ Start of week optional ✕ Number of weekly transitions optional ✕ Number of daily transitions optional ✕ Temperature setpoint hold optional ✕ Temperature setpoint hold duration optional ✕ Thermostat programming operation mode optional ✕ Thermostat running state optional ✕ Setpoint change source optional ✕ Setpoint change amount optional ✕ Setpoint change source timestamp optional ✕ Occupied setback optional ✕ Occupied setback min optional ✕ Occupied setback max optional ✕ Unoccupied setback optional ✕ Unoccupied setback min optional ✕ Unoccupied setback max optional ✕ Emergency heat delta optional ✕ Ac type optional ✕ Ac capacity optional ✕ Ac refrigerant type optional ✕ Ac compressor type optional ✕ Ac error code optional ✕ Ac louver position optional ✕ Ac coil temperature optional ✕ Ac capacityformat optional ✕ Preset types optional ✕ Schedule types optional ✕ Number of presets optional ✕ Number of schedules optional ✕ Number of schedule transitions optional ✕ Number of schedule transition per day optional ✕ Active preset handle optional ✕ Active schedule handle optional ✕ Presets optional ✕ Schedules optional ✕ Setpoint hold expiry timestamp optional ✕ Max thermostat suggestions optional ✕ Thermostat suggestions optional ✕ Current thermostat suggestion optional ✕ Thermostat suggestion not following reason optional Enabled features: Heating
🌀 Fan speed control	v1.1	✕

Sensors
▶ 💧 Humidity sensor	v1.0	✓
Relative Humidity Measurement Information available: ✓ Current humidity reading ✓ Minimum measurable humidity ✓ Maximum measurable humidity ✕ Tolerance
🌡️ Temperature sensor	v1.0	✕

Automation & Scenes
🎬 Scenes & presets	v1.3	✕
⏰ Scheduling	v1.0	✕

Comfort & Climate
▶ 🔥 Heating	v1.0	✓
Thermostat What you can do: ✓ Setpoint raise lower ✓ Get weekly schedule response ✕ Set weekly schedule optional ✕ Get weekly schedule optional ✕ Add thermostat suggestion response optional ✕ Clear weekly schedule optional ✕ Set active schedule request optional ✕ Set active preset request optional ✕ Add thermostat suggestion optional ✕ Remove thermostat suggestion optional ✕ Atomic response optional ✕ Atomic request optional Information available: ✓ Current room temperature ✕ Outdoor temperature optional ✕ Occupancy optional ✓ Abs min heat setpoint limit ✓ Abs max heat setpoint limit ✕ Abs min cool setpoint limit optional ✕ Abs max cool setpoint limit optional ✕ Pi cooling demand optional ✕ Pi heating demand optional ✕ Hvac system type configuration optional ✕ Local temperature calibration optional ✕ Occupied cooling setpoint optional ✓ Target heating temperature ✕ Unoccupied cooling setpoint optional ✕ Unoccupied heating setpoint optional ✕ Min heat setpoint limit optional ✕ Max heat setpoint limit optional ✕ Min cool setpoint limit optional ✕ Max cool setpoint limit optional ✕ Min setpoint dead band optional ✕ Remote sensing optional ✓ Control sequence of operation ✓ System mode ✕ Thermostat running mode optional ✕ Start of week optional ✕ Number of weekly transitions optional ✕ Number of daily transitions optional ✕ Temperature setpoint hold optional ✕ Temperature setpoint hold duration optional ✕ Thermostat programming operation mode optional ✕ Thermostat running state optional ✕ Setpoint change source optional ✕ Setpoint change amount optional ✕ Setpoint change source timestamp optional ✕ Occupied setback optional ✕ Occupied setback min optional ✕ Occupied setback max optional ✕ Unoccupied setback optional ✕ Unoccupied setback min optional ✕ Unoccupied setback max optional ✕ Emergency heat delta optional ✕ Ac type optional ✕ Ac capacity optional ✕ Ac refrigerant type optional ✕ Ac compressor type optional ✕ Ac error code optional ✕ Ac louver position optional ✕ Ac coil temperature optional ✕ Ac capacityformat optional ✕ Preset types optional ✕ Schedule types optional ✕ Number of presets optional ✕ Number of schedules optional ✕ Number of schedule transitions optional ✕ Number of schedule transition per day optional ✕ Active preset handle optional ✕ Active schedule handle optional ✕ Presets optional ✕ Schedules optional ✕ Setpoint hold expiry timestamp optional ✕ Max thermostat suggestions optional ✕ Thermostat suggestions optional ✕ Current thermostat suggestion optional ✕ Thermostat suggestion not following reason optional Enabled features: Heating
❄️ Cooling	v1.0	✕
🔄 Auto heat/cool	v1.0	✕
📌 Temperature presets	v1.0	✕
💧 Humidity control	v1.1	✕

⚠ Not available: Scheduling

Technical Details For developers

▼

Device Compatibility

Can provide data to: These devices have client clusters that can read from or control this device's server clusters

Thermostat (3 devices)

Aqara Climate Sensor W100 (Aqara) Eve Thermo Control (Eve Systems) Touchscreen Switch S100 (Aqara)

Relative Humidity Measurement (1 device)

Touchscreen Switch S100 (Aqara)

Spec Compliance & Feature Analysis

Comparing this device's clusters against Matter specification requirements. Shows what's implemented, what's missing, and bonus features. Note: Legacy clusters (e.g., Scenes) count as compliant when replaced by newer equivalents (Scenes Management).

Thermostat Matter 1.0 Compliant

★ ★ ★ ☆ ☆ ☆ Feature Score:

50%

Optional Not Implemented 7

Per the Matter spec, these clusters are optional. The device is compliant without them.

Groups Thermostat User Interface Configuration Energy Preference Fan Control (client) Temperature Measurement (client) Relative Humidity Measurement (client) Occupancy Sensing (client)

Extra (Beyond Spec) 1

Descriptor

2/2 required | 0/7 optional

Humidity Sensor Matter 1.0 Compliant

★ ★ ★ ☆ ☆ Feature Score:

60%

Extra (Beyond Spec) 1

Descriptor

2/2 required | 0/0 optional

Frequently Paired With Found in 34 installations

These devices are commonly found together in the same smart home setup based on anonymous telemetry data.

BILRESA dual button IKEA of Sweden

12 shared 35.3% of installs

tado Wireless Temperature Sensor X tado° GmbH

9 shared 26.5% of installs

BILRESA scroll wheel IKEA of Sweden

9 shared 26.5% of installs

tado Smart Thermostat X tado° GmbH

8 shared 23.5% of installs

KLIPPBOK water leak sensor IKEA of Sweden

8 shared 23.5% of installs

Aqara Door and Window Sensor P2 Aqara

8 shared 23.5% of installs

Lafaer Wireless Radar Occupancy Sensor GL.iNet

6 shared 17.6% of installs

MYGGBETT door/window sensor IKEA of Sweden

6 shared 17.6% of installs

Endpoints by Version